Schedule Service Now

 

Right here below you will find some brilliant news involving How to Install a Bathtub.

Installing a bathtub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately tough project. If the old bathtub is conveniently accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old tub as well as place the brand-new tub, the task is a lot harder. In either case, the project is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the brand-new one. Make certain you have actually qualified on your own for the task and fit trying it. As opposed to employing a specialist to take control of a halfway-completed project, it is far better to think about employing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This post will certainly help you install a brand-new bathtub in your washroom if you have currently gotten a new tub and also don't require to transform the arrangement of your previous water supply pipelines.
Your tools and product list need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Planning for the Installation

To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before going on to fit the new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bath tub

Making use of both wood boards under its feet, put the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Turn on the water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if required. Load the bath tub as well as additionally examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling and also sealing around the tub must wait till the tub has actually been used at least when as this will certainly resolve it right into its final placement.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Secure the faucet in place with the maker given backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Tub

In the area where the bath satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, creating the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with dampness and possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can split fairly early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate reader on Tools You Need to Install a New Bathtub , I assumed sharing that portion was a good idea. Make sure you take the opportunity to distribute this blog posting if you liked it. Thanks so much for taking the time to read it.

Rely on our emergency expertise.